View AD8156-EVALZ_1001323.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

6.25 gbps, 4 4, digital crosspoint switch with eq ad8156 rev. 0 information furnished by analog devices is believed to be accurate and reliable. however, no responsibility is assumed by analog devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. specifications subject to change without notice. no license is granted by implication or otherwise under any patent or patent rights of analog devices. trademarks and registered trademarks are the property of their respective owners. one technology way, p.o. box 9106, norwood, ma 02062-9106, u.s.a. tel: 781.329.4700 www.analog.com fax: 781.461.3113 ?2007 analog devices, inc. all rights reserved. features 4 4, fully differential, nonblocking array configurable for dual 2 2 operation dc to 6.25 gbps per channel, nrz data rate programmable input equalization compensates for over 40 of fr-4 at 6.25 gbps multicast and broadcast modes of operation programmable output swing 100 mv p-p to 1.6 v p-p differential power supply: 3.3 v (10%) low power no eq: 400 mw typical maximum eq: 700 mw typical inputs: ac-coupled or dc-coupled wide set of dc-coupled input standards 3.3 v/2.5 v/1.8 v cml or 3.3 v lvpecl control: lvttl- or lvcmos-compatible low additive jitter: 25 ps p-p typical low random jitter: 0.8 ps rms integrated 50 termination impedance at inputs/outputs individual output disable for power savings 49-ball, 8 mm 8 mm bga, 1 mm pitch applications backplane equalization sonet/sdh gigabit ethernet xaui fibre channel functional block diagram eq 4 4 cs rst upd we re mode d[3:0] a[3:0] control logic ad8156 in0p/n in1p/n in2p/n in3p/n out0p/n out1p/n out2p/n out3p/n eq eq eq output drivers input receivers input equalization 4 4 switch 06305-001 figure 1. general description the ad8156, a member of the xstream line of products, is a high speed, fully differential, digital crosspoint switch. the part can function as a 4 4 crosspoint switch with double-latched memory, allowing simultaneous updates, or as a dual 2 2 with direct output control. the ad8156 has low power dissipation, typically 700 mw on 3.3 v with all outputs and input equalizers active. it operates at any data rate from dc to 6.25 gbps per port. each input channel on the ad8156 has a programmable input equalizer to compensate for signal loss over a backplane. the ad8156 high speed inputs are compatible with both ac- coupled and dc-coupled 3.3 v, 2.5 v, or 1.8 v cml, as well as 3.3 v lvpecl data levels. the control interface is lvttl- and lvcmos-compatible at 3.3 v. all input and output termination resistors are integrated for ease of layout and to minimize impedance mismatch. input equalization and unused outputs can be individually disabled to minimize power dissipation. the ad8156 is packaged in a 49-ball, 8 mm 8 mm, bga package with a 1 mm ball pitch. it operates over the industrial temperature range of ?40c to 85c.
ad8156 rev. 0 | page 2 of 20 table of contents features .............................................................................................. 1 applications ....................................................................................... 1 functional block diagram .............................................................. 1 general description ......................................................................... 1 revision history ............................................................................... 2 specifications ..................................................................................... 3 electrical specifications ............................................................... 3 timing specifications .................................................................. 4 timing diagrams .............................................................................. 5 absolute maximum ratings ............................................................ 7 thermal resistance ...................................................................... 7 esd caution .................................................................................. 7 pin configurations and function descriptions ........................... 8 typical performance characteristics ............................................. 9 test circ u it ...................................................................................... 12 theory of operation ...................................................................... 13 4 4 mode ................................................................................... 13 dual 2 2 mode ......................................................................... 13 input equalization ...................................................................... 14 control interface description ....................................................... 15 control pins ................................................................................ 15 address pins, a[3:0] inputs ...................................................... 16 data pins, d[3:0] inputs/outputs ............................................ 16 control interface levels ............................................................ 16 programming examples ................................................................ 17 dual 2 2 mode (mode pin = 1) programming examples ............................................................ 17 4 4 mode (mode pin = 0) programming examples ........ 17 outline dimensions ....................................................................... 19 ordering guide .......................................................................... 19 revision history 5 /07revision 0: initial version
ad8156 rev. 0 | page 3 of 20 specifications electrical specifications v tti = v tto = v cc = 3.3 v, v ee = 0 v, r l = 50 , differential output swing = 800 mv, ac-coupled, data rate = 6.25 gbps, prbs 2 23 ?1, v in = 1 v p-p differential, t a = 25c, unless otherwise noted. table 1. parameter symbol conditions min typ max unit dynamic performance maximum data rate nrz data 6.25 gbps deterministic jitter data date < 6.25 gbps 25 ps p-p random jitter 0.8 ps rms propagation delay t pd input to output 1000 ps propagation delay match 50 ps output fall time t f differential, 20% to 80% 75 ps output rise time t r differential, 20% to 80% 75 ps input characteristics input voltage swing v in differential 200 2000 mv p-p input voltage range single-ended v ee + 1.5 v cc v input voltage range v cm common-mode v ee + 1.6 v cc v input termination r in single-ended 50 output characteristics output voltage swing v out differential, programmable 50 800 1850 mv p-p output voltage range common-mode v ee + 1.6 v cc v output termination r out single-ended 50 power supply v cc operating range v cc v ee = 0 v 3.0 3.3 3.6 v supply current i cc 1 all disabled 19 ma i cc 1 all outputs on, no equalization 67 ma i cc 1 all outputs and equalizers on 141 ma i tti 800 mv differential swing 32 ma i tto 800 mv differential swing 32 ma power dissipation 2 all disabled 60 mw all outputs on, no equalization 400 mw all outputs and equalizers on 700 mw thermal characteristics operating temperature range ?40 85 c logic input characteristics v cc = 3.3 v dc input v in high 2.0 v cc v input v in low 0 0.8 v 1 i cc supply current excludes input and output termination curre nts. currents at v tti and v tto count in power dissipation, but are not included in i cc . note that in a cml output structure with separate ter mination supplies, all of the output and input current is drawn from v tti and the termination resistors, not from vcc. 2 power dissipation includes power due to 800 mv p-p different ial input and output voltages; this is the true representation of power dissipated on and used by the chip at an 800 mv p-p diff erential signal level.
ad8156 rev. 0 | page 4 of 20 timing specifications v tti = v tto = v cc = 3.3 v, v ee = 0 v, r l = 50 , differential output swing = 800 mv, ac-coupled, data rate = 6.25 gbps, prbs 2 23 ? 1, v in = 1 v p-p differential, t a = 25c, unless otherwise noted. table 2. parameter symbol min typ max unit first rank write cycle cs to we setup time t csw 0 ns address setup time t asw 0 ns data setup time t dsw 1 ns we to cs hold time t chw 0 ns address hold time t ahw 0 ns data hold time t dhw 0 ns we pulse width t wp 10 ns second rank update cycle cs to upd setup time t csu 0 ns upd to cs hold time t chu 0 ns output enable t uoe 20 ns output switch t uot 10 ns output disable t uod 20 ns upd pulse width t uw 10 ns transparent write and update cycle output enable t woe 35 50 ns output toggle t wot 25 45 ns output disable t wod 25 45 ns second rank readback cycle cs to re setup time t csr 0 ns re to cs hold time t chr 0 ns addr from re t rha 5 ns data from re t rde 15 ns access time t aa 15 30 ns re to read disable t rdd 50 ns asynchronous reset output disable t tod 10 25 ns rst pulse width t tw 10 ns
ad8156 rev. 0 | page 5 of 20 timing diagrams d[3:0] a [3:0] we cs t csw t asw t wp t dsw t dhw t ahw t chw 06305-002 figure 2. first rank write cycle cs upd outxn/p enable outxn/p disable outxn/p toggle t uod t uot t uoe t csu t uw t chu 06305-003 figure 3. second rank update cycle
ad8156 rev. 0 | page 6 of 20 cs upd we outxn/p enable outxn/p disable outxn/p toggle t woe t wod t wot t whu 06305-004 figure 4. transparent write and update cycle data[3:0] addr[3:0] addr1 addr2 data2 data1 re cs t csr t rde t aa t rha t chr t rdd 06305-005 figure 5. second rank readback cycle t tod t tw outxn/p disable rst 06305-006 figure 6. asynchronous reset
ad8156 rev. 0 | page 7 of 20 absolute maximum ratings table 3. parameter rating v cc to v ee 3.6 v v tti v cc + 0.6 v v tto v cc + 0.6 v internal power dissipation 1 1.92 w input voltage v cc + 0.6 v logic input voltage v ee ? 0.3 v < v in < v cc + 0.6 v storage temperature range ?65c to +125c junction temperature 150c lead temperature range 300c 1 specification for t a = 25c. stresses above those listed under absolute maximum ratings may cause permanent damage to the device. this is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. thermal resistance ja is specified for the worst-case conditions, that is, a device soldered in a circuit board for surface-mount packages. table 4. thermal resistance package type ja jc unit 49-ball csp_bga 65 28 c/w esd caution
ad8156 rev. 0 | page 8 of 20 pin configurations and function descriptions a b c d e f g 7654321 06305-007 v ee in1n in1p v tti in0n in0p v cc in2p v ee d3 v ee mode v cc out0p in2n d0 d2 rst we cs out0n v tti v ee d1 v ee upd v cc v tto in3p a0 a1 a3 re v cc out1p in3n v cc a2 v ee v ee v ee out1n v cc out3n out3p v tto out2n out2p v ee figure 7. pin configuration (bottom view) table 5. pin function descriptions pin no. mnemonic description a1 v ee negative supply. a2 in1n high speed input complement. a3 in1p high speed input. a4 v tti input termination supply. a5 in0n high speed input complement. a6 in0p high speed input. a7 v cc positive supply. b1 in2p high speed input. b2 v ee negative supply. b3 d3 input address pin (msb). b4 v ee negative supply. b5 mode mode select pin. b6 v cc positive supply. b7 out0p high speed output. c1 in2n high speed input complement. c2 d0 input address pin (lsb). c3 d2 input address pin. c4 rst reset/disable outputs. c5 we first bank write enable. c6 cs chip select enable. c7 out0n high speed output complement. d1 v tti input termination supply. d2 v ee negative supply. d3 d1 input address pin. d4 v ee negative supply. pin no. mnemonic description d5 upd second bank write enable. d6 v cc positive supply. d7 v tto output termination supply. e1 in3p high speed input. e2 a0 address pin (lsb). e3 a1 address pin. e4 a3 address pin (msb). e5 re second bank read enable. e6 v cc positive supply. e7 out1p high speed output. f1 in3n high speed input complement. f2 v cc positive supply. f3 a2 address pin. f4 v ee negative supply. f5 v ee negative supply. f6 v ee negative supply. f7 out1n high speed output complement. g1 v cc positive supply. g2 out3n high speed output complement. g3 out3p high speed output. g4 v tto output termination supply. g5 out2n high speed output complement. g6 out2p high speed output. g7 v ee negative supply.
ad8156 rev. 0 | page 9 of 20 typical performance characteristics v tti = v tto = v cc = 3.3 v, v ee = 0 v, r l = 50 , differential output swing = 800 mv, ac-coupled, data rate = 6.25 gbps, prbs 2 23 ? 1, v in = 1 v p-p differential, t a = 25c, unless otherwise noted. 06305-008 50ps/div 200mv/di v figure 8. input eye diagram at 3.2 gbps,10 fr4 06305-009 50ps/div 200mv/di v figure 9. input eye diagram at 3.2 gbps, 40 fr4 06305-010 25ps/div 200mv/di v figure 10. input eye diagram at 6.25 gbps, 10 fr4 06305-011 50ps/div 200mv/di v figure 11. output eye diagram at 3.2 gbps, 10 fr4, optimal eq 06305-012 50ps/div 200mv/di v figure 12. output eye diagram at 3.2 gbps, 40 fr4, optimal eq 06305-013 25ps/div 200mv/di v figure 13. output eye diagram at 6.25 gbps, 10 fr4, optimal eq
ad8156 rev. 0 | page 10 of 20 06305-014 25ps/div 200mv/di v figure 14. input eye diagram at 6.25 gbps, 40 fr4 0 deterministic jitter (ps p-p) differential input (v p-p) 1.0 0.5 2.0 1.5 2.5 6.25gbps 3.2gbps 06305-015 35 0 30 25 20 15 10 5 figure 15. deterministic jitter vs. input signal level (no eq) 35 0 06 deterministic jitter (ps p-p) input data rate (gbps) 30 25 20 15 10 5 2 15 43 7 deterministic jitter 06305-016 figure 16. deterministic jitter vs. data rate (no eq) 06305-017 25ps/div 200mv/di v figure 17. output eye diagram at 6.25gbps, 40 fr4, optimal eq 35 0 ?40 80 deterministic jitter (ps) temperature (c) 30 25 20 15 10 5 0 ?20 60 40 20 6.25gbps 06305-019 figure 18. deterministic jitter vs. temperature (optimal eq, 20 fr4) 35 0 0.1 10 eq gain (db) frequency (ghz) 30 25 20 15 10 5 1 06305-020 figure 19. input eq gain vs. frequency
ad8156 rev. 0 | page 11 of 20 50 0 5 10 15 20 25 30 35 40 45 3.0 3.1 3.2 3.3 3.4 3.5 3.6 06305-022 deterministic jitter (ps p-p) v cc (v) figure 20. deterministic jitter vs. v cc 50 0 5 10 15 20 25 30 35 40 45 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 06305-023 deterministic jitter (ps p-p) output termination voltage (v) figure 21. deterministic jitter vs. output termination voltage 800 0 100 200 300 400 500 600 700 01234567 9 8 06305-024 eye height (mv) data rate (gbps) figure 22. eye height vs. data rate
ad8156 rev. 0 | page 12 of 20 test circuit data out *single-ended representation in0p/n ad8156 in1p/n in2p/n in3p/n out0p/n out1p/n out2p/n out3p/n fr4 test backplane 2 2 2 2 2 2 2 2 2 50? cables 50? 50 ? 50? cables 50? cables high speed sampling oscilloscope pattern generator ac-coupled evaluation board 50? 50? 06305-021 differential stripline traces 8mils wide, 8mils space, and 8mils dielectric height trace lengths = 10", 20", 30", and 40" figure 23. ad8156 test circuit
ad8156 rev. 0 | page 13 of 20 theory of operation the ad8156 is a 4 4 crosspoint switch with programmable input equalization and programmable output current levels. it can be used as a nonblocking and fully programmable 4 4 crosspoint switch, or as a dual 2 2 protection switch with fast channel switching. each lane can run at any rate from dc to 6.25 gbps independent of the other lanes. in 4 4 mode, the user writes the control data to double-latched memory cells through a simple cpu interface. connectivity, individual output disables, output current level, and input equali- zation are all individually programmable. broadcast addresses can be used to simultaneously program the functionality of all channels. a global reset disables the part and resets all equalizers and output current levels to their default states. a chip select pin can be used in applications where a single bus is controlling multiple switches. when in dual 2 2 mode, the part functions as two individual 2 2 switches whose connectivity is asynchronously controlled by the d3 to d0 pins, and output enable is controlled by the a3 to a0 pins. the dual 2 2 mode allows for sub-10 ns output channel switching or output enable. output swing control and input equalization cannot be controlled in dual 2 2 mode because all the data and address pins are used as asynchronous control pins. however, settings are retained when switching modes, so the user can set the desired swing and input equalization settings in 4 4 mode on startup and then switch to dual 2 2 mode. the user can switch at will between 4 4 mode and dual 2 2 mode by toggling the mode pin. when switching from 4 4 mode to dual 2 2 mode, eq and output current settings are retained, but the output connectivity control is instantly switched to the asynchronous interface of a[3:0] and d[3:0]. to have uninterrupted data flow when switching from 4 4 mode to dual 2 2 mode, the address and data pins should be set into the desired states for dual 2 2 mode before changing the mode pin. when switching from dual 2 2 mode to 4 4 mode, eq and the output current settings are also retained, but the connectivity specified by the values of a[3:0] and d[3:0] when mode went low are retained in memory. until some other connectivity is set using the 4 4 control interface, the last dual 2 2 mode settings are stored in memory. 4 4 mode pulling the mode pin low puts the ad8156 in 4 4 mode. in this mode, the chip is controlled by the values stored in the on- chip memory. this memory is organized as two banks of latches; the second bank controls the chip, and the first bank allows the next set of configuration data to be written while the chip is operat- ing based on the second bank data. to write to the first bank of memory, the user sets data and address to the desired states and pulls we low. this writing process is repeated until all desired configuration data is stored in the first bank of latches, and then the chip configuration is simultaneously updated by pulling upd low. if desired for verification, the value of the second bank of latches can be read back by pulling re low. when re is low, data pin d3 to data pin d0 are driven by the chip. the timing of this operation is shown in figure 5 . because the interface is entirely asynchronous, the only limitation on the timing of the read cycle is that each period must be a minimum of 15 ns. connectivity control connection between an output and an input is set by addressing a specific output and connecting it to an input. each output has a disable bit. table 10 shows how to set the crosspoint connectivity. output current control output current is controlled by addressing a specific output and choosing the output current. the output current is equal to 2 ma + (2 ma d[3:0] ) for example, the default code for d[3:0] is b0111. therefore, the output current level is 2 ma + (2 ma 7) = 16 ma. table 11 and table 13 show how to set the output current levels. input equalization control input equalization is set per input lane. the equalization is set in ~1.53 db steps, from 0 db to 23 db of equalization at 3.125 ghz (roughly corresponding to a 6.25 gbps bit rate). the amount of equalization is ghz83.0 log40 15 )( 10 f d[3:0] fgain = a value of 0000 disables the equalizer, saving power. global setting by writing to one of three broadcast addresses, the user can set all connectivity, output current, or input equalization settings to the same value. broadcast addresses are controlled similarly to other control addresses. see table 12 , table 13 , and table 14 for broadcast mode programming. dual 2 2 mode pulling the mode pin high puts the ad8156 in dual 2 2 mode. in this mode, the part is asynchronously controlled by the address and data pins, a[3:0] and d[3:0], respectively. in dual 2 2 mode, the switch is configured as two individual 2 2 switches, and each output can be individually disabled. out0 and out1 can be connected to either in0 or in1, and out2 and out3 can connect to either in2 or in3. there are no connectivity options in dual 2 2 mode to connect out0/out1 to in2/in3, or out2/out3 to in0/in1. in dual 2 2 mode, input equalization and output level settings are not accessible. if these functions are needed, the user should program these functions in 4 4 mode and then return to dual 2 2 mode. output swing and equalization settings are retained from 4 4 mode to dual 2 2 mode. readback is not available in dual 2 2 mode.
ad8156 rev. 0 | page 14 of 20 when in dual 2 2 mode, the a[3:0] and d[3:0] pins set the ad8156 configuration state when cs is low. this configuration method allows the user to have multiple ad8156s share the control bus while each device has its own dedicated cs control signal. eq ad8156 in0p/n in1p/n in2p/n in3p/n vcc mode out0p/n out1p/n out2p/n out3p/n eq eq eq output drivers input receivers input equalization 2 2 switch 2 2 switch 0 6305-008 figure 24. ad8156 in dual 2 2 mode input equalization the ad8156 input equalization is an active scheme that is fully linear over all operating ranges. the useful range of equalization covers dc to 3.125 ghz frequencies or dc to 6.25 gbps data rates. other key features include: ? 15 steps of gain, linear in db, programmable through the 4 4 control interface ? gain has a 40 db per decade slope ? peak gain of 23 db at 3.125 ghz (~6.25 gbps) ? equalizes more than 40 of typical fr4 backplane with associated connectors and vias at all speeds ? 0.10 ui p-p residual deterministic jitter typ @ 3.125 gbps ? 0.15 ui p-p residual deterministic jitter typ @ 6.25 gbps as with all equalizers, the gain setting is the key. the ideal method of choosing the proper gain setting is to run the equalizer with the channel, and choose the setting with minimum jitter. if this process is not possible or is too time consuming for the number of channels required, the loss of the channel at 3.125 ghz should be measured. the best equalizer setting is usually 2 db to 4 db more than the loss at 3.125 ghz. using the 40 db slope of the equalizer gain, the gain at other frequencies can be calculated based on the peak gain at 3.125 ghz. the formula to use is ghz83.0 log40 15 )( 10 f d[3:0] fgain = where f is the fundamental frequency of the data, or the data rate divided by 2 (that is, 6.25 gbps f = 3.125 ghz). performance of the equalizer is heavily dependent on the channel used. operation at high speeds depends on features such as dielectric used (for example, fr4, nelco3000, or rogers), connector quality, via stub length, and routing geometry and topology.
ad8156 rev. 0 | page 15 of 20 control interface description the control interface for the ad8156 consists of a set of address, data, and several control pins. all control pins are active low. the control interface is level sensitive. control pins all control pins on the chip are level-sensitive, not edge-triggered. the preferred programming method is to assert the data and address pins to their desired configuration, wait one control bit period, then pull we low to write to the first bank of registers. after one control bit period, we is pulled high. after an additional control bit period, the address and data pins can be set to their next values, and the cycle repeats. using this method, each write takes three control bit periods. after the first bank of registers is programmed, upd is pulled low, which transfers the data from the first bank of latches to the second bank of latches. when upd is pulled low, the full chip updates, regardless of the status of the address, data, we , or re pins. wr it ing to the par t while upd is pulled low writes through the first bank of registers and into the second bank, immediately affecting the connectivity and output current of the part. it is recommended that the user write to the first bank with one data bit cycle, and subsequently activate the upd pin low, because data and address pin skews presented to the part can lead to errors when writing through both banks simultaneously. if skews are properly controlled, a transparent write can allow a very quick change of states in 4 4 mode. rst pin at any time, a reset pulse to rst can be applied to the control interface to globally reset all first and second bank latches to their default values. the device has an internal power-on reset circuit, but it is recommended that rst be held low during power-up. the default values for the chip include disabling all outputs, turning off equalization, and setting output current code to the default, b0111 (16 ma). the de fault connection is the buffer state, or in0 out0, in1 out1, in2 out2, in3 out3; all outputs are connected but disabled. rst overrides all of the other control pins. cs pin the chip select pin, an active low signal, facilitates multiple chip address decoding. all control signals, except the reset signal, are ignored when cs is pulled high. the pin disables the control signals and does not affect operation of the chip. cs does not power down any of the latches, preserving any data programmed in the latches. mode pin the mode pin sets the part in 4 4 mode or dual 2 2 mode. pulling mode low sets the part in 4 4 mode, and pulling mode high sets the part in dual 2 2 mode. in dual 2 2 mode, the we , re , and upd pins are unused. we pin this pin is the write enable to the first bank of registers. forcing we to logic low allows the data on the d[3:0] pins to be stored in the first bank of latches for the function specified by a[3:0]. the we pin must be returned to logic high state before changing the other pins after a write cycle to avoid overwriting the first bank data. upd pin this pin is the write enable to the second bank of registers. forcing upd to logic low transfers the data stored in all first bank latches to the second bank latches, which is the active set of registers. the chip functions update during this operation. re pin this pin is the read enable for the second bank of registers. forcing re to logic low enables the on-chip drivers to drive the bidirectional d[3:0] pins. the on-chip drivers are only intended to drive high impedance loads, so any external drivers of d[3:0] must be disabled when re is low. table 6. basic control pin functions rst cs mode we re upd function 1 1 x x x x control interface disabled. prior settings are stored, and the chip is run based on the configuration data stored (in 4 4 mode) or set (in dual 2 2 mode) previously. 0 x x x x x global reset. disables all outputs and eq ualizers. output current code set to 0111 (16 ma). 1 0 0 1 1 1 4 4 mode. address and data pins are ignored (values in the ad8156 memory control connectivity, output current, and eq setting). 1 0 0 0 1 1 write enable. writes to the first bank of registers. 1 0 0 1 0 1 readback enable. reads back data on d[3:0] from the addressed latch (second bank of registers). 1 0 0 1 x 0 global update. transfers data from first bank of registers to second bank of registers (active set). chip functions update. 1 0 0 0 x 0 transparent write. writes and updates simultaneou sly through first bank to the second bank of registers. chip functions update. 1 0 1 x x x dual 2 2 mode. address and data pins asynchronously control the device.
ad8156 rev. 0 | page 16 of 20 address pins, a[3:0] inputs the ad8156 feature sets can be set port by port or globally. a[3:2] specify what is being programmed or read back when the part is being configured port by port. connectivity, output current, equalization, or global programming features are chosen based on the values of a[3:2]. similarly, a[1:0] address the port that is being programmed or read back. in global programming, a[1:0] serve a different function. refer to table 9 to table 15 for programming examples. data pins, d[3:0] inputs/outputs in readback mode, the d[3:0] pins are low impedance outputs indicating the stored values in the memory to be read. the readback drivers are designed to drive high impedances only, so external drivers connected to d[3:0] must be disabled during readback mode. control interface levels the ad8156 control interface shares the data path supply pins, v cc and v ee . the potential between the positive logic supply v cc and the negative supply v ee must be at least 3.0 v and no more than 3.7 v. regardless of supply, the logic threshold is approximately one-half the supply range, allowing the interface to be used with most lvcmos- and lvttl-logic drivers. table 7. dual 2 2 mode programming table address a[3:0] data d[3:0] input a3 to input a0 enable output 3 to output 0, respectively . input d3 to input d0 control the connectivity of output 3 to ou tput 0, respectively. 1 = enables the output (for all a[3:0] inputs ) 0 = input 2, 1 = input 3 (for d2 and d3) 0 = disables the output (for all a[3:0] inputs) 0 = input 0, 1 = input 1 (for d0 and d1) table 8. 4 4 mode programming table mode address a[3:0] data d[3:0] 0 0 a1 a0 0 d2 d1 d0 write/read connectivity and disable a1 and a0 determine which output is being programmed. d1 and d0 determine which input is connected to which output; d2 determines the enabled/disabled state of that output, with d2 = 1 (enable). when writing or reading, d3 is always 0. 0 1 a1 a0 d3 d2 d1 d0 write/read output current level a1 and a0 determine which output is being programmed. d0 to d3 binarily program the output current level/voltage swing with the output current = 2 ma + (2 ma decimal (d[3:0])). 1 0 0 0 0 d2 d1 d0 broadcast connectivity/disable d1 and d0 determine which input is connected to all of the outputs. d2 determines the enabled/disabled stat e of all outputs with d2 = 1 (enable). when writing or reading, d3 is always 0. 1 0 0 1 d3 d2 d1 d0 broadcast output current level d0 to d3 binarily program the output current level/voltage swing with the output current = 2 ma + (2 ma decimal (d[3:0])). the value is written to all outputs. broadcast eq setting 1 0 1 1 d3 d2 d1 d0 data inputs d0 to d3 set the in put equalization level where: gain(f ) = d[3:0]/15 40 log 10 (f/0.83 ghz). program eq setting 1 1 a1 a0 d3 d2 d1 d0 a1 and a0 determine which input is being programmed. d0 to d3 set the input equalization level, where: gain(f ) = d[3:0]?15 40 log 10 (f?0.83 ghz).
ad8156 rev. 0 | page 17 of 20 programming examples a[3:0] d[3:0] we upd 06305-009 figure 25. sample timing diagram for 4x4 mode programming examples dual 2 2 mode (mode pin = 1) programming examples table 9. dual 2 2 mode programming address pins data pins a3 a2 a1 a0 d3 d2 d1 d0 description 1 0 0 0 0 x x x a[3] = 1 enables out3. d[3] = 0 connects in2 to out3. 1 0 0 0 1 x x x a[3] = 1 enables out3. d[3] = 1 connects in3 to out3. 1 1 0 0 0 0 x x a[3:2] = b11 enables out2 and out3. d[3:2] = b00 connects in2 to both out2 and out3. 1 1 0 0 1 0 x x a[3:2] = b11 enables out2 and out3. d[3:2] = b10 connects in2 to out2 and connects in3 to out3. 0 0 1 0 x x 0 x a[1] = 1 enables out1. d[1] = 0 connects in0 to out1. 0 0 1 1 x x 1 1 d[1:0] = b11 enables out0 and out1. d[1:0] = b11 connects in1 to both out0 and out1. 1 1 1 1 0 1 0 1 a[3:0] = b1111 enables all outputs. d[3:0] = b010 1 connects in2 to out3, in3 to out2, in0 to out1, in1 to out0. 4 4 mode (mode pin = 0) programming examples table 10. connectivity programming, a[3:2] = b00 address pins data pins a3 a2 a1 a0 d3 d2 d1 d0 description 0 0 0 0 0 1 0 0 a[1:0] = 0 selects out0. d2 = 1 enables out0. d[1:0] = 0 connects in0 to out0. 0 0 0 0 0 0 0 0 a[1:0] = 0 selects out0. d2 = 0 disables out0. d[1:0] = 0 connects in0 to out0. 0 0 1 0 0 1 0 1 a[1:0] = b10 selects out2. d2 = 1 enables out2. d[1:0] = b01 connects in1 to out2. 0 0 1 1 0 1 0 0 a[1:0] = b11 selects out3. d2 = 1 enables out3. d[1:0] = b00 connects in0 to out3. table 11. output level programming, a[3:2] = b01 address pins data pins a3 a2 a1 a0 d3 d2 d1 d0 description (output current = 2 ma + (2 ma d[3:0]) 0 1 0 0 0 1 0 0 a[1:0] = 0 selects out0. d[3:0] = b0100 sets out0 current to 2 ma + (2 ma 4) = 10 ma. 0 1 0 0 1 0 0 0 a[1:0] = 0 selects out0. d[3:0] = b1000 sets out0 current to 2 ma + (2 ma 8) = 18 ma. 0 1 1 0 1 1 0 1 a[1:0] = b10 selects out2. d[3:0] = b1101 sets out2 current to 2 ma + (2 ma 13) = 28 ma. 0 1 1 1 0 0 0 0 a[1:0] = b11 selects out3. d[3:0] = b0000 sets out3 current to 2 ma + (2 ma 0) = 2 ma.
ad8156 rev. 0 | page 18 of 20 table 12. broadcast connectivit y programming, a[3:0] = b1000 address pins data pins a3 a2 a1 a0 d3 d2 d1 d0 description 1 0 0 0 0 1 0 0 d2 = 1 enables all outputs. d[1:0] = b00 connects in0 to all outputs. 1 0 0 0 0 1 1 1 d2 = 1 enables all outputs. d[1:0] = b11 connects in3 to all outputs. 1 0 0 0 0 0 1 0 d2 = 0 disables all outputs. d[1:0] = b10 connects in2 to all outputs, but all outputs are disabled. table 13. broadcast output le vel programming, a[3:0] = b1001 address pins data pins a3 a2 a1 a0 d3 d2 d1 d0 description (output current = 2 ma + (2 ma d[3:0]) 1 0 0 1 0 1 0 0 d[3:0] = b0100 sets current of all outputs to 2 ma + (2 ma 4) = 10 ma. 1 0 0 1 1 1 0 1 d[3:0] = b1101 sets current of all outputs to 2 ma + (2 ma 13) = 28 ma. 1 0 0 1 0 0 0 0 d[3:0] = b0000 sets current of all outputs to 2 ma + (2 ma 0) = 2 ma. table 14. broadcast equalization (eq) programming, a[3:0] = b1011 address pins data pins a3 a2 a1 a0 d3 d2 d1 d0 description (gain(f) = d[3:0]?15 40 log 10 (f?0.83 ghz)), assume f = 2.25 ghz 1 0 1 1 0 1 0 0 d[3:0] = b0100 sets all input eq = (4/15 40 log 10 (2.25 ghz/0.83 ghz)) = 4.6 db. 1 0 1 1 1 1 0 1 d[3:0] = b1101 sets all input eq = (13/15 40 log 10 (2.25 ghz/0.83 ghz)) =14.95 db. 1 0 1 1 0 0 0 0 d[3:0] = b0000 sets all input eq = (0/15 40 log 10 (2.25 ghz/0.83 ghz)) = 0 db. table 15. individual input eq programming, a[3:2] = b11 address pins data pins a3 a2 a1 a0 d3 d2 d1 d0 description (gain(f) = d[3:0]?15 40log 10 (f?0.83 ghz)), assume f = 2.25 ghz 1 1 0 0 0 1 0 0 a[1:0] = b00 selects in0. d[3:0] = b0100 sets eq = (4/15 40 log 10 (2.25 ghz/0.83 ghz)) = 4.6 db. 1 1 0 1 1 1 0 1 a[1:0] = b01 selects in1. d[3:0] = b1101 sets eq = (13/15 40 log 10 (2.25 ghz/0.83 ghz)) = 14.95 db. 1 1 1 0 1 1 1 1 a[1:0] = b10 selects in2. d[3:0] = b1111 sets eq = (15/15 40 log 10 (2.25 ghz/0.83 ghz)) = 17.25 db. 1 1 1 1 0 0 0 0 a[1:0] = b11 selects in3. d[3:0] = b0000 sets eq = (0/15 40 log 10 (2.25 ghz/0.83 ghz)) = 0 db.
ad8156 rev. 0 | page 19 of 20 outline dimensions ball diameter 74 5 63 2 1 6.00 bsc sq a1 corner index area a b c d e f g bottom view seating plane detaila 0.70 0.60 0.50 coplanarity 0.20 * 1.31 1.21 1.10 * 1.85 1.71 1.50 top view 1.00 bsc ball a1 pad corner detail a 0.25 min 8.20 8.00 sq 7.80 * compliant with jedec standards mo-192-abb-1 with exception to package height and thickness. 012006-0 figure 26. 49-ball chip scale package ball grid array [csp_bga] (bc-49-3) dimensions shown in millimeters ordering guide model temperature range package description package option ad8156abcz 1 ?40c to +85c 49-ball chip scale package ball grid array [csp_bga] bc-49-3 AD8156-EVALZ 1 evaluation board 1 z = rohs compliant part.
ad8156 rev. 0 | page 20 of 20 notes ? 2007 analog devices, inc. all rights reserved. trademarks and registered trademarks are the property of their respective owners. d06305-0- 5/07(0)

▲Up To Search▲

Price & Availability of AD8156-EVALZ

	To Download AD8156-EVALZ Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .